LED Cube/Cube Soldering Manual: Unterschied zwischen den Versionen

Aus Wiki CCC Göttingen
Zur Navigation springen Zur Suche springen
Zeile 21: Zeile 21:
</gallery>
</gallery>
==LED Bending==
==LED Bending==
In the second step we have to bend the legs of the LEDs so you can assemble them without much mechanical stress on the wires. First, take one LED:
In the second step we have to bend the legs of the LEDs so you can assemble them without much mechanical stress on the wires. Be careful with the next steps - they are deciding how your cube looks like. Also, try to bend the wires correct the first time and not wiggle much on them, they tend to break off if you overdo it. First, take one LED:
<gallery>
<gallery>
File:cs3-004.jpeg
File:cs3-004.jpeg
</gallery>
</gallery>


Hold it upside down and make sure that the longer of the two legs is the left one, the shorter the right one. Then bend the shorter 90 degrees towards you. The result should look like this:
<gallery>
<gallery>
File:cs3-005.jpeg
File:cs3-005.jpeg
<gallery>
</gallery>
File:cs3-006.jpeg
File:cs3-006.jpeg
File:cs3-007.jpeg
File:cs3-007.jpeg

Version vom 17. April 2012, 20:20 Uhr

Vorlage:LED Cube Series This page of the LED Cube Series will guide you through the process of building the Cube structure of the LED Cube. Building this structure is not really hard, but it may be a bit frustrating if the wires do not want like you. This is normal and your first cube will most probably not look perfect. However, this is a beginner workshop, so there will be much to learn.

LED preparation

How this first step will look somewhat depends on your LEDs. For now we will only clear LED bodies with one color:

Thus, if you have matt LEDs, you do not have to care about this step.

The clear see-through LEDs have a big advantage over the matt ones: You can see through them and thus the illusion of free hanging lights is much better. However, they also have a notable disadvantage: They have a very small cone of light coming out at the top. This makes it nearly impossible to look into them from above, they nearly don't shine from the side and LEDs from below will also illuminate LEDs above them. A very good workaround at this point is to grab a sheet of fine sand paper and to sand the top surface of the LED. Here you can see the difference:

Repeat this step with all LEDs, if you want. Try not to bend the legs to much, as this will on one hand stress them and on the other hand make your cube look less regular. (Of course, you may want such a cube - that is your decision. ;) .)

LED Bending

In the second step we have to bend the legs of the LEDs so you can assemble them without much mechanical stress on the wires. Be careful with the next steps - they are deciding how your cube looks like. Also, try to bend the wires correct the first time and not wiggle much on them, they tend to break off if you overdo it. First, take one LED:

Hold it upside down and make sure that the longer of the two legs is the left one, the shorter the right one. Then bend the shorter 90 degrees towards you. The result should look like this:

File:cs3-006.jpeg File:cs3-007.jpeg File:cs3-008.jpeg File:cs3-009.jpeg File:cs3-010.jpeg File:cs3-011.jpeg File:cs3-012.jpeg File:cs3-013.jpeg File:cs3-014.jpeg File:cs3-015.jpeg File:cs3-016.jpeg File:cs3-017.jpeg File:cs3-018.jpeg File:cs3-019.jpeg File:cs3-020.jpeg File:cs3-021.jpeg File:cs3-022.jpeg File:cs3-023.jpeg File:cs3-024.jpeg File:cs3-025.jpeg File:cs3-026.jpeg File:cs3-027.jpeg File:cs3-028.jpeg File:cs3-029.jpeg File:cs3-030.jpeg File:cs3-031.jpeg File:cs3-032.jpeg File:cs3-033.jpeg File:cs3-034.jpeg File:cs3-035.jpeg File:cs3-036.jpeg File:cs3-037.jpeg File:cs3-038.jpeg File:cs3-039.jpeg File:cs3-040.jpeg </gallery>