Schliesssystem/Technische Dokumentation

Schema

{Laptop,Handy,Tablet} <-> WRT <-> ethernet GPIO device <-> {Keymatic <-> Schloss, Sprechanlage <-> Aussentuer, ERT}

DING

Command Interface

The DING listens on *:2701/tcp for incoming connections. The protocol is ECMD with doorctl extensions.

mode set

doorctl mode set <mode>

sets the mode #Mode. Once you issued this command, you will have to wait a short amount of time before doorctl mode set and doorctl inner door open are enabled again.

mode get

doorctl mode get

returns the currently selected #Mode.

inner door open

doorctl inner door open. 

retracts the safety catch of the inner door. Once you issued this command, you will have to wait a short amount of time before doorctl mode set and doorctl inner door open are enabled again.

? inner door open

doorctl ? inner door open

checks if the inner door is currently opened. This does not mean, that the safety catch is retracted but that the door is really standing open.

outer door open

doorctl outer door open

opens the outer door.

Mode

The DING has a mode register for the inner door that is always set to one of the following values:

Mode	Default	LED value	Comment	ERT effect
locked	X	*-R-R--	door is locked	nothing if door is closed, switch to unlocked if door is opened
unlocked		*O-----	door is unlocked	nothing if door is closed, switch to unlocked+ert if door is opened
unlocked+ert		*----GG	door is unlocked	retract safety catch if door is closed, switch to primed mode if door is opened
primed		*ORRRGG	door will be locked a few seconds after it has been closed	nothing
any		***R***	keymatic is currently performing an action	nothing

Led colors: R: Red, O: Orange, G: Green, *: Any color, italic: blinking

To modify modes use the #mode set or #mode get commands. Also, you can cycle through modes using the pushbutton on the DING.

Pinout

• relais 1: keymatic.lock
• relais 2: keymatic.unlock
• relais 3: siedle.open
• relais 4: do not connect this relay!
• relais ?: siedle.ring
• relais 5: keymatic.open

Connector pinout

These are the pinouts of the two flat cables coming from entryphone and keymatic.

Siedle entryphone

• Pin 1: door opener connector a
• Pin 2: door opener connector b
• Pin 3: ERT connector a
• Pin 4: ERT connector b
• Pin 5: Siedle ERT input a
• Pin 6: Siedle ERT input b
• Pin 7-10: not used

Keymatic

• Pin 1: Pushbutton lock/unlock (?)
• Pin 2: Pushbutton common
• Pin 3: Pushbutton lock/unlock (?)
• Pin 4: RI common
• Pin 5: RI dooropener
• Pin 6: RI lock/unlock (?)
• Pin 7: RI lock/unlock (?)
• Pin 8: unused
• Pin 9: RI power supply +
• Pin 10: RI power supply -

Todo

• Gemeinsame Stromversorgung
  • Fritzbox (12 V/ 100 mA)
  • brickme (12 V / 2.5 A)
  • Keymatic (12 V / 100 mA)
  • DING (5V / 500 mA)
  • Telefon (6 V / 300 mA)
  • Motorola-Box (5 V / 3 A)
  • Spacemaster 6000 (5 V / 400 mA)

Logbuch

8.2.2012

Relay für keymatic.open hat nicht reagiert. Wir standen vor der Tür, Tür hat entriegelt aber nicht geöffnet.

Transistor am Relay 6 nach gelötet. Danach wieder vollständige Funktion.... Hat das Relay irgendetwas mit .open zu tuen?

Datei:AlexN900 01 20120208 001.jpg