LED Flower

PCB

PCB

Generated PCB preview

BOM

Necessary

Designator	Value	Part-No	Price / EUR	Count	Sum / EUR
R1	3.6 kΩ, 1206	R:	0.01	1	0.01
R2	2.7 kΩ, 1206	R:	0.01	1	0.01
R3, R4	68 Ω, 1%, 1206	CSD: 10-120068	0.01	2	0.02
R5..R19, R38..R40	3.6 kΩ, 1206	R:	0.01	18	0.18
R20..R31	100 Ω, 1206	R:	0.01	12	0.12
R32..R37	150 Ω, 1206	R:	0.01	6	0.06
B1..B3	0 Ω, 1206	R:	0.01	3	0.03
T1..T18	BC807-25, SOT23	R: BC 807-25 SMD	0.04	18	0.72
C1, C2, C3	100 nF, 16 V, 0603	R: X7R-G0603 100N	0.05	3	0.15
C4, C5	22 pF, 0603	R: NPO-G0603 22P	0.05	2	0.10
C6	10 uF, 10 V, 0805	R: X5R-G0805 10/16	0.07	1	0.07
C9	100 nF, 63 V, 1206	R: X7R-G1206 100N	0.05	1	0.05
D2, D3	3.6 V Zener Diode, MiniMELF	R: SMD ZF 3,6	0.05	2	0.10
X1	20 MHz	R: 20,0000-HC49U-S	0.18	1	0.18
ISP, ADC, PWR	12-pin break-away connector (from a 36-pin strip)	R: SL 1X36W 2,54	0.27	1	0.27
CONN_USB	USB B connector	R: USB BW	0.21	1	0.21
U1	ATmega88-20AU	R: ATMEGA 88-20 AU	2.95	1	2.95
LED1..LED6	RGB LED	?	0.30	6	1.80
24 Copper wires	40 cm copper wire cutoff	R: CUL 500/0,63	13.90	0.058	0.81
Sum					7.84

Version 1: USB Powered

Designator	Value	Part-No	Price / EUR	Count	Sum / EUR
L1	10 uH, 450 mA, 1210	CSD: 146-121R010	0.22	1	0.22
U2, C7, C8	Do not populate		0.00	0	0.00
Sum					0.22

Version 2: Externally powered

Designator	Value	Part-No	Price / EUR	Count	Sum / EUR
U2	LM1117-5.0	CSD: LM1117DT-5,0V	0.95	1	0.95
C7, C8	10 uF, 10 V, 0805	R: X5R-G0805 10/16	0.07	3	0.21
D1	1N4001, MELF	R: X7R-G1206 100N	0.04	1	0.04
L1	Do not populate		0.00	0	0.00
Sum					1.20

Option: Button

Designator	Value	Part-No	Price / EUR	Count	Sum / EUR
R41	3.6 kΩ, 1206	R:	0.01	1	0.01
BTN	Pushbutton	?	0.10	1	0.10
Sum					0.11

Tutorial

Soldering the Components onto the PCB

Microcontroller

The first step in soldering this board is also the most difficult: Soldering the microcontroller. We are going to use the drag soldering technique. To do so, we first place the microcontroller on the board to get an idea of how it should be placed afterwards. Note the pin one mark which is a small dip in one corner of the IC. This is used to orient it correctly:

• 

Now remove the microcontroller again, select one pad of the pcb and tin it. For this and the next two steps, you don't have to worry about any solder bridges, we will remove them afterwards.

• 
• 
• 

Now grab the microcontroller with a pair of tweezers, heat up the tinned pad and place the microcontroller correctly. Do not overheat the microcontroller: If you are not able to position the microcontroller within about 10 seconds remove the soldering iron and try again after waiting a short amount of time.

• 
• 
• 

To further secure it, also solder one pin on the opposite corner.

• 
• 

Now select one edge of the microcontroller that has not been used in the previous steps and add some Flux to pins. What comes now is not easy and probably may require multiple attempts: Solder some pins one on side of the edge at once and then just slide the soldering iron slowly and without any pressure to the other side:

• 
• 
• 

If you have done everything right (right speed, correct amound of solder and flux) all pins will be soldered to the board and there will be no bridges between them:

• 

If you have created any bridges, there are two ways to get rid of them:

• Drag the solder away from the microcontroller.
• Use a desoldering gun or desoldering wig.

However, repeat this process for the three other edges that are not yet soldered completely:

• 

Decoupling Capacitors

To operate, the microcontroller needs a set of decoupling capacitors. These are two-padded components, so we will esentially replicate the first steps of the microcontroller soldering process:

• Tin one pad,
• add the component and
• solder the other side.

The first one is C9, a 100 nF capacitor in a 1206 package, the biggest of the capacitors included in this kit:

• 
• 
• 
• 
• 
• 
• 
• 

Now continue with C1 using the same process. C1 is also a 100 nF capacitor, but in a 0603 package.

• 
• 
• 
• 

And now C2 and C3, both the same capacitor as C1.

• 
• 

Crystal Oscillator

Next step is the crystal oscillator. To prepare for that, we will first solder the capacitors C4 and C5 which are both 22 pf 0603 capacitors.

• 
• 

The crystal oscillator then goes directly on the other side of the pcb below those two capacitors. Just put it in and solder both pins.

• 

  Position of the Crystal

• 

  From the bottom

• 

  Solder both pins

Then clip off anything that is above the solder joint.

• 

  Clip off the excess wire

Programming and Analog Input Headers

Now we add two headers, one for programming the microcontroller, one for the analog input of the microcontroller. Again, the headers are on the back side of the PCB.

• 
• 

Now simply solder each pin to the PCB:

• 
• 

First Test

Get a lab power supply and set the maximum voltage to 5 V and the maximum current to zero. Connect the positive terminal (red) and negative terminal (black) as shown in the picture below:

•