TVBGone/en - Versionsgeschichte

Marvin am 15. April 2012 um 03:23 Uhr

2012-04-15T03:23:10Z

← Nächstältere Version		Version vom 15. April 2012, 03:23 Uhr
Zeile 1:		Zeile 1:
	[[Datei:tvbgone.png\|right\|200px\|thumb\|left\|TVbgone with two SMD LEDs and two normal 5mm LEDs]]This is a clone of the normal [http://www.ladyada.net/make/tvbgone/index.html TVBGone Kit]. TVBGone is a board, that tries to switch off every TV device. This one is ~~build~~ with almost only SMD parts, this board is smaller than the original.		[[Datei:tvbgone.png\|right\|200px\|thumb\|left\|TVbgone with two SMD LEDs and two normal 5mm LEDs]]This is a clone of the normal [http://www.ladyada.net/make/tvbgone/index.html TVBGone Kit]. TVBGone is a board that tries to switch off every TV device. This one is built with almost only SMD parts, this board is smaller than the original.

	== PCB ==		== PCB ==

2011-11-11T13:19:54Z

Englische Kategorie hinzugefügt

← Nächstältere Version		Version vom 11. November 2011, 13:19 Uhr
Zeile 119:		Zeile 119:

	__FORCETOC__		__FORCETOC__
	[[Category:Projekte]][[Category:Bausaetze]]		[[Category:Projekte]][[Category:Bausaetze]][[Category:En]]

2011-11-10T16:35:09Z

Kategorie Bausätze hinzugefügt

← Nächstältere Version		Version vom 10. November 2011, 16:35 Uhr
Zeile 119:		Zeile 119:

	__FORCETOC__		__FORCETOC__
	[[Category:Projekte]]		[[Category:Projekte]][[Category:Bausaetze]]

2011-09-15T18:28:15Z

Part I

← Nächstältere Version		Version vom 15. September 2011, 18:28 Uhr
Zeile 86:		Zeile 86:
	# Start soldering with the uC (ATTINY85V)		# Start soldering with the uC (ATTINY85V)
	# C3 and C4 both 22pF,0603		# C3 and C4 both 22pF,0603
	# Go on with R1(1 kΩ, 0805) and C1(100nF,0603)		# Go on with R3(1 kΩ, 0805) and C1(100nF,0603)
	# With soldering the plug connector and the Batteryclip you ended this part - Mind the polarity of the battery clip!		# With soldering the plug connector and the Batteryclip you ended this part - Mind the polarity of the battery clip!
	# XTAL1 (8 MHz, on the other side)		# XTAL1 (8 MHz, on the other side)

2011-09-15T18:02:19Z

Part I

← Nächstältere Version		Version vom 15. September 2011, 18:02 Uhr
Zeile 85:		Zeile 85:
	===Part I===		===Part I===
	# Start soldering with the uC (ATTINY85V)		# Start soldering with the uC (ATTINY85V)
	# ~~Now solder the crystal oscillator XTAL1 (8 MHz, on the other side),C2~~ and C3 both 22pF,0603		# C3 and C4 both 22pF,0603
	# Go on with R1(1 kΩ, 0805) and C1(100nF,0603)		# Go on with R1(1 kΩ, 0805) and C1(100nF,0603)
	# With soldering the plug connector and the Batteryclip you ended this part - Mind the polarity of the battery clip!		# With soldering the plug connector and the Batteryclip you ended this part - Mind the polarity of the battery clip!
			# XTAL1 (8 MHz, on the other side)

	===Part II - Programming ===		===Part II - Programming ===

2011-09-08T13:25:49Z

Part III

← Nächstältere Version		Version vom 8. September 2011, 13:25 Uhr
Zeile 108:		Zeile 108:

	===Part III===		===Part III===
	Take the next part of your choice and solder it :) Please mind the polarity of LED5!		Take the next part of your choice and solder it :) Please mind the polarity of LED5 (for the actual package, the green dot is the cathode)!


	===Testing===		===Testing===

2011-08-27T20:42:04Z

← Nächstältere Version		Version vom 27. August 2011, 20:42 Uhr
Zeile 108:		Zeile 108:

	===Part III===		===Part III===
	Take the next part of your choice and solder it :)		Take the next part of your choice and solder it :) Please mind the polarity of LED5!

2011-08-27T20:06:27Z

download Firmware v1.2

← Nächstältere Version		Version vom 27. August 2011, 20:06 Uhr
Zeile 92:		Zeile 92:
	All parts are on the PCB - now start with programming the board.		All parts are on the PCB - now start with programming the board.

	# download the ~~sources~~ from [http://www.ladyada.net/make/tvbgone/download.html TVBGone/download.html] and use a programmer of your choice. The software you need is descibed on this site: [[AVR Toolchain]]).		# download the firmware v1.2 from [http://www.ladyada.net/make/tvbgone/download.html TVBGone/download.html] and use a programmer of your choice. The software you need is descibed on this site: [[AVR Toolchain]]).
	# test for short circuit		# test for short circuit
	# plug in the programmer Port P1		# plug in the programmer Port P1

2011-08-27T20:03:54Z

last part of the turorial

@@ Zeile 90: / Zeile 90: @@
 ===Part II - Programming ===
-Now all parts are on the PCB for programming the board. So download the sources from [http://www.ladyada.net/make/tvbgone/download.html TVBGone/download.html] and use a programmer of your choice.
+All parts are on the PCB - now start with programming the board.
 __FORCETOC__
 [[Category:Projekte]]

2011-08-27T19:29:28Z

Tutorial PartI & Part II

← Nächstältere Version		Version vom 27. August 2011, 19:29 Uhr
Zeile 18:		Zeile 18:
	P2:		P2:

	1 - Vcc		1 - Vcc

	2 - GND		2 - GND
Zeile 79:		Zeile 79:
	\| \|\|Batteryclip \|\| {{pollin\|94-270188}} \|\| 0.15 \|\| 1 \|\| 0.15		\| \|\|Batteryclip \|\| {{pollin\|94-270188}} \|\| 0.15 \|\| 1 \|\| 0.15
	\|}		\|}


			==Tutorial==

			===Part I===
			# Start soldering with the uC (ATTINY85V)
			# Now solder the crystal oscillator XTAL1 (8 MHz, on the other side),C2 and C3 both 22pF,0603
			# Go on with R1(1 kΩ, 0805) and C1(100nF,0603)
			# With soldering the plug connector and the Batteryclip you ended this part - Mind the polarity of the battery clip!

			===Part II - Programming ===
			Now all parts are on the PCB for programming the board. So download the sources from [http://www.ladyada.net/make/tvbgone/download.html TVBGone/download.html] and use a programmer of your choice.

	__FORCETOC__		__FORCETOC__
	[[Category:Projekte]]		[[Category:Projekte]]